Kapcsolat

Hétfőtől péntekig 8:00 és 17:00 között szívesen személyesen is állunk rendelkezésére. Ezen a linken keresztül találja meg a régió kapcsolattartóit.

Wolfurti központ
+43 5574 6706-0

Az Ön kapcsolattartója

Áruház

{{warenkorbCtrl.warenkorb.items.length}}

Bevásárlókosár {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} Árucikkek Bevásárlókosár váltás

Megjegyzés

Kép

Árucikkek

db

Egységár

Teljes ár

Teljes ár kedvezményekkel

{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

A rendelés folytatásához kérjük jelentkezzen be, hogy láthassa az árait.

Guiding and centring elements for die casting

Flat guiding units, standard guiding systems as well as guiding systems for large dies can be found in our wide range of products. The centring and locating rings are perfectly adapted to die casting applications.

Szabvány vezetések

Szabvány vezetések

High-quality guiding elements matched to our extensive range of cavity plates
Guiding system with two fitting diameters for an optimal fit in the guiding hole

Laposvezetők

Compensation of thermal expansion
Also usable for large dies
Robust design

Flat guiding unit comparison

Laposvezetők

CENTRING

To compensate for the thermal expansion due to temperature differences in the die casting moulds we offer locks and centring units in different variations and sizes. Of course these are supplied ready-to-use and interchangeable as individual parts.

E 1304 TOP LOCK

E 1304 TOP LOCK

Installation through vertical machining from the split line face
Best wear resistance through the DLC coating
Available up to width 96 mm

E 1352 CENTRING UNIT

For highest centring accuracy
Easy introduction through round design
Best wear resistance through the DLC coating

E 1352 CENTRING UNIT

E 1306 FINE CENTRING UNIT

E 1306 FINE CENTRING UNIT

For high-precision centring tasks
Space-saving installation due to small fitting dimensions
Best wear resistance through the DLC coating

LOCATING RINGS, SHIMS AND THREAD INSERTS

Our perfectly coordinated range of locating rings, shims and thread inserts is ideally suited for your die casting needs.

LOCATING RING WITH NECK AND BORE

LOCATING RING WITH NECK AND BORE

E 1365: without screw holes
E 1367: with screw holes

E 2680 AND E 2682 SHIMS

For easy adjustment of the cavity plates with cleared split line faces
Round and rectangular plates with matching lengths and diameters
The rounded corners enable precise installation and prevent dirt accumulation

E 2680 AND E 2682 SHIMS

E 1516 THREADED INSERT FOR EJECTOR SET

E 1516 THREADED INSERT FOR EJECTOR SET

Replaces the thread that is usually too short in the ejector set
Coordinated to the thread size of the die casting machine
In 2 different variations with anti-rotation blocking

Vállalat

Meusburger Georg GmbH & Co KG
Kesselstr. 42
6960 Wolfurt | Austria

+43 5574 6706
office@meusburger.com

Quick Links

@ 2023 Meusburger

Hírlevél

Közösségi média

Meusburger M © 2022 by Meusburger Georg GmbH & Co KG | All rights reserved